amrapali builders @@ hardware hacking and robotics using the raspberry pi.pdf

CLASSROOM CHALLENGE
HARDWARE HACKING AND ROBOTICS USING THE
RASPBERRY PI
In this lesson you will learn how to extend the Raspberry Pi’s capability by connecting it to other hardware components.
You will then be able to program the Raspberry Pi to control the additional hardware. The Raspberry Pi is a simple
microcomputer that presents exciting opportunities to design and build new systems. Experimenting with computers
and electronic components to extend their capabilities is termed“hardware hacking”. There are many examples of
interesting projects here: http://www.raspberrypi.org/archives/tag/hardware and here: http://www.tech-fruits.com/
archives/category/raspberry-pi-hardware.
By completing this activity you will be able to connect components to the Raspberry Pi to build a simple robotic buggy
and to program it to move using Scratch. In order to protect the Raspberry Pi from the higher voltages required to
operate the motors of the robotic buggy, you will connect an interface board such as the Piface, developed by the
University of Manchester School of Computer Science. You will learn how to ensure that the software recognises the
Piface hardware and is able to communicate with it. Once you have learned how to connect and use the input and
output ports of the Piface, you will be able to extend this activity to create other devices using your own ideas. More
Piface projects and information can be found at: http://piface.openlx.org.uk.
The stages of building the robotic buggy are:
• Setting up the basic hardware and using the emulator to check that the software and hardware can communicate
successfully.
• Adding and controlling simple components such as turning an LED on and off and adding a buzzer.
• Writing programs in Scratch to control inputs and outputs.
• Building a robotic buggy and writing a program in Scratch to control its movement.
RESOURCES NEEDED FOR THIS ACTIVITY
• Raspberry Pi
• Piface interface board
• Construction materials e.g. Lego to make a buggy with a base and wheels
• 2 x motors to drive two front wheels
• Batteries and battery snaps/holders
• Breadboard, LEDs, buzzer, resistors, jump wires

TASK 1 – SETTING UP THE BASIC HARDWARE (10 minutes)
Set up the Raspberry Pi as shown below. You will also need an interface board to connect to your Pi to control
components such as motors as they require a higher current (and often a higher voltage) to operate. This provides
protection to the Raspberry Pi’s components by using a device called a relay to turn the motor on or off.
This image shows the Raspberry Pi’s GPIO (General Purpose Input
Output) connector. The Raspberry Pi operates at
5v DC and it is possible to connect components that do not draw a
large current e.g. LEDs (Light Emitting Diodes) without using an
interface board. However, you still need to ensure that you know the
voltage required so that you do not cause damage to the Raspberry Pi.
In this image, a Piface interface board has been connected to the
Raspberry Pi. This allows you to connect a wide range of hardware
components but also protects the Raspberry Pi. The operating system
installed onto the SD card is slightly different from the standard
Raspbian Wheezy Debian Linux image. It contains code to allow the
Piface to operate with Scratch and Python to write control programs.
The Piface connects to the Raspberry Pi’s GPIO connector. If you are
doing this, make sure that you are very gentle and that the rubber foot
sits on the Pi to keep the board level.

Below are steps for setting up the Raspberry Pi ready to use. You will need to repeat these steps every time you want to
use the Pi with the Piface:
1. Connect up a USB hub with a keyboard and mouse and plug in the power supply. Boot up the Pi and login using
the username pi and password raspberry unless a separate user account has been set up in which case your
teacher will tell you what to type in.
2. Enter startx at the raspberrypi$ prompt.
3. Click on the Scratch icon on the desktop. Do NOT click on the Scratch Piface Handler link!
4. Click and hold the Shift key on the keyboard and click on the Share menu item in Scratch and select Host
Mesh. You should see a pop up showing the IP address 127.0.0.1. Click OK.
5. Minimise Scratch and click on the LX terminal link on the desktop.
6. Type the following at the prompt:
cd piface/scratch
python scratch_handler.py 127.0.0.1
You should then see some output showing that the Piface is now connected.
Note: You will need to repeat step 4–6 each time you close Scratch or the LX terminal window. If you find that a
program appears not to be connecting to the Piface, run these steps just in case the connection has been lost.
Piface emulator
Scratch
LX Terminal

USING THE PIFACE EMULATOR
The Piface version of the Raspbian operating system also has an icon on the desktop to the Piface Emulator. This allows
you to check the connection with the device.
Click override enable.
Click on output with
Piface connected.
LED now indicates
output is on.

TASK 2 – CONNECTING SIMPLE COMPONENTS - CONTROLLING
AN LED (10 minutes)
The Piface has 8 LEDs connected to its output ports. These can easily be programmed to turn on and off. Output ports 1
and 2 are also connected to the two relays.
Firstly connect Scratch to the Piface as detailed in Task 1.
1. Click on Variables then Make a variable.
2. Name the variable piface-output1.
3. Repeat this until you have created variables for piface-outputs 2 to 8.

4. Create the program below. Each output can only have a value of 0 (off) or 1 (on).
Think about what the program will do before you run it. The space bar being pressed acts as input to begin the
program.
5. Change the program so that it turns the LEDs on and then off in sequence so that only one LED is lit at any
moment.
6. Write another program that turns on the odd number outputs (1,3,5,7) and then turns them off and turns the
even number LEDs on (2,4,6,8). This sequence should repeat 3 times.
The Piface also has 4 push button switches that can be used for input to trigger an output. The following program uses a
switch input.
7. Change the program so that piface-input1 switches on piface-output1 and piface-inputs 2, 3 and 4 switch on
the outputs with the same number.

TASK 3 – ADDING A BUZZER (10 minutes)
The Raspberry Pi or Piface are not supplied with any sound output devices however, it is possible to connect a
piezo buzzer like the one shown below.
1. Connect the buzzer as shown below. The rightmost port is the 5v output and you also need to connect the
negative wire of the buzzer to another output port.
TASK 4 – CONTROLLING MOTORS (10 minutes)
Another very useful output device is a motor. This allows us to create devices that move. To begin with, you will connect
a DC motor to an output port on the Piface. However, electric motors often draw more current than other devices and
may operate at a higher voltage that would damage the Raspberry Pi. To provide protection, the Piface has two relays
installed. A relay is an electrical switch that allows a low powered circuit to turn on a higher powered one. However, the
two circuits are isolated. Relays are also used to switch on a car starter motor (a high powered circuit) when the key is
turned in the ignition (a low powered circuit).
Each relay has three connecting pins. The centre pin is common. You should always connect to this port. The top pin of
the three is called Normally Closed you should connect to this pin when you want the relay to break the circuit when
it is activated. The bottom pin is Normally Open which will cause the relay to close the circuit when activated. Since we
wish to turn a motor on when the relay is switched, we need to connect one wire to the common and the other to the
Normally Open port.
5v connection
Output ports 1–8. In this
example, the buzzer has been
connected to output 8.
Buzzer
Normally Closed
Common
Normally Open

The motor illustrated comes from a Lego kit. Its operating voltage is 9v. This is being supplied by a 9v battery connected
in the circuit.
TASK 5 – BUILDING A ROBOT (30 minutes)
Using a construction kit or individual components, you are now going to create a robotic buggy controlled by the
Raspberry Pi with a fitted Piface. Your buggy will need four wheels with two being driven by motors each connected to a
relay on the Piface as shown here:
Battery
Motor
Common connection to relay 2
(connects to output 2)
Normally Open connection to relay
2 (connects to motor battery)
Common connection to relay 1
(connects to output 1)
Normally Open connection to relay 1
(connects to second motor battery)

TASK 6 – PROGRAMMING THE ROBOT (30 minutes)
1. Connect the robotic buggy to the Piface relays as outlined above.
2. Check that Scratch is connected to the Raspberry Pi as in Task 1.
3. Create a program to move the buggy by turning the motors on and off.
4. The above program moves the buggy in a straight line. Turning one motor off will cause the buggy to turn. Write
a program to move the buggy so that it moves and turns to effectively“draw”a square and return to its original
starting position.
The finished robot buggy.

TASK 7 – INVESTIGATING HOW ROBOTS ARE USED (30 minutes)
Through your investigation, you have learned that the robotic buggy is controlled by a program that switches the
relay driving the motor on and off as required. This can also be controlled by sensors as input devices. Robotic output
devices are called actuators. They may be motors but could also be pneumatic or hydraulic devices.
Robots are used in a number of different industries e.g. car manufacture, nuclear power plants, military applications,
space exploration and even medicine. There are advantages and disadvantages associated with their use. It is important
that robots are reliable as they are often used in safety-critical environments or in remote situations where maintenance
and repair would be very costly e.g. space.
In this task, you will investigate and research the use of robots. You should focus on:
• The uses of robots giving specific examples
• Why it is important that they are reliable
• What input and output devices are used in the examples that you have given
• Try to find information about how they are programmed
Create a presentation of your findings.
Here are some useful websites:
http://en.wikipedia.org/wiki/Robotics
http://www.nasa.gov/audience/foreducators/robotics/home/index.html
http://spectrum.ieee.org/robotics/

amrapali builders @@ hardware hacking and robotics using the raspberry pi.pdf

More Related Content

Viewers also liked

Similar to amrapali builders @@ hardware hacking and robotics using the raspberry pi.pdf

More from amrapalibuildersreviews

Recently uploaded

amrapali builders @@ hardware hacking and robotics using the raspberry pi.pdf